Golden Queen Announces Initial Drill Results from the 2018 Main Pit 2 Infill Drilling Program

2018-04-03 / @newswire

 

VANCOUVER, April 3, 2018 /CNW/ - Golden Queen Mining Co. Ltd. (TSX:GQM; OTCQX:GQMNF) (the "Company" or "Golden Queen") is pleased to announce drill results for the first five holes at its 50%-owned Soledad Mountain gold-silver mine located south of Mojave, California. 

The drill results are part of the Company's 2018 Main Pit 2 Infill Drilling program. The holes GQ-824 through GQ-828 drilled to date have been successful in intersecting and geologically verifying existing shallow mineralized zones in and around the currently mined East Pit, and has also been successful in exploring for and intersecting deeper mineralized zones. In some cases, some new mineralized zones have been identified.

Each hole listed in the table below has intersected strong alteration envelopes and locally significant gold/silver mineralization associated with the Patience and Queen Esther zones, and has encountered the deeper Silver Queen target along with other mineralized zones.

Several key features have been initially observed in the drill cuttings of these five holes:

  • There appears to be an interplay of the relatively high-grade Slusher vein with the lower-grade Patience zone. Some holes show distinct Slusher vein and Patience zones; while in other holes, these two zones appear to perhaps merge in a large swath of strong alteration;
  • Several unnamed or unknown mineralized zones have been intersected to date, usually situated between the Patience and Queen Esther zones. Previous interpretations suggest that these zones may be subparallel to the Queen Esther structure, may be relatively flat-lying, and locally carry significant gold and silver grades (see accompanying table). Further work and interpretation must be completed to determine whether gold/silver grades encountered so far in these structures show good continuity from section to section. It is worthy to note that the current drilling program was designed to explore new areas around the Queen Esther and Silver Queen veins for potential ore zones that could expand the current pit design;
  • The Silver Queen deep target appears, at least initially, to be locally composed of two fault splays. These two splays can locally merge (as in the case of the Silver Queen vein observed near surface), but underneath the East Pit these two Silver Queen splays appear to have a shallower dip than previously interpreted and they range, on average, from about 100'-120' apart. The grades from these two Silver Queen splays intersected underneath the central and western portions of the East Pit have been rather low and erratic, but the assays received and the structural integrity of the splays has been much stronger from underneath the east end of the East Pit (hole GQ-828). These structures appear to get stronger to the east and southeast; and
  • Hole GQ-828 is also the hole that was planned to be the farthest east from the Main Pit 2 Infill Drilling Program. Other than the Patience and Karma zones, no major structures have been previously interpreted and projected onto the cross section that contains this hole. Significant zones of strong alteration and locally significant gold/silver mineralization below the Patience and Karma zones were encountered in this hole and this suggests that deeper mineralization does extend to the southeast from the East Pit. Future drilling should step out from this area in an east/southeast direction and continue to test for additional mineralization.

In general, the true thickness of the various mineralized zones is estimated at 75-95% of the mineralized interval in the drill hole. The table below highlights the assay results and initial observations to date:









Hole #

Hole
depth

(feet)

Drilled
interval (feet)

Length of
drilled
interval
in hole
(feet)

Estimated
true
thickness of
drilled
interval
(feet)

Au (opt)

Ag (opt)

Structure

GQ-824

1085

110 - 125

15

13.4

0.041

0.37

Slusher



175 – 215

40

36.2

0.004

0.25

Patience



365 – 380

15

14.6

0.028

0.07

Unnamed



410 – 430

20

19.3

0.036

0.12

Unnamed



585 – 595

10

9.4

0.014

0.41

Queen Esther



705 – 710

5

4.6

0.056

0.03

Silver Queen



835 – 840

5

4.4

0.016

0.43

Silver Queen

GQ-825

1210

70 – 90

20

18.8

0.024

0.70

Slusher



130 – 160

30

28.3

0.014

0.27

Patience



240 – 260

20

19.2

0.011

0.06

Unnamed



295 – 300

5

4.8

0.015

0.02

Unnamed



365 – 370

5

4.7

0.026

0.02

Unnamed



480 – 495

15

14.0

0.022

0.21

Queen Esther



530 – 535

5

4.7

0.017

1.68

Queen Esther



805 – 820

15

13.6

0.002

0.12

Silver Queen



915 – 945

30

27.9

0.002

0.17

Silver Queen

GQ-826

1050

40 – 45

5

4.5

0.077

0.42

Slusher



80 – 95

15

13.5

0.050

0.60

Patience



245 – 250

5

4.9

0.010

0.04

Unnamed



290 – 295

5

4.9

0.010

0.03

Unnamed



410 – 420

10

9.6

0.082

0.15

Unnamed



520 – 535

15

14.2

0.025

0.57

Queen Esther



750 – 755

5

4.6

0.002

0.13

Silver Queen



840 – 845

5

4.5

0.004

0.21

Silver Queen

GQ-827

1045

15 – 20

5

3.6

0.026

0.50

Slusher



170 – 185

15

13.9

0.083

0.53

Patience



205 – 210

5

4.7

0.021

0.13

Patience



450 – 460

10

8.9

0.047

0.34

Queen Esther



735 – 740

5

4.1

0.010

0.22

Silver Queen



860 – 875

15

11.7

0.002

0.10

Silver Queen

GQ-828

1100

15 - 25

10

7.1

0.013

0.19

Karma



50 – 55

5

3.7

0.010

0.13

Karma



70 – 75

5

3.7

0.026

0.53

Karma



215 – 235

20

18.5

0.045

0.33

Patience



315 – 320

5

4.8

0.012

0.04

Unnamed



385 – 395

10

9.5

0.019

0.09

Queen Esther



415 - 420

5

4.7

0.017

0.06

Queen Esther



685 – 695

10

9.1

0.025

0.60

Silver Queen



800 – 805

5

4.4

0.029

0.98

Silver Queen

 

The following figure illustrates the geographic parameters of the drill program to date:

*Drawing illustrates the farthest extents of both the current modeled resources/reserves and the structures of interest to the drilling program.  The Slusher vein is a small, but slightly higher-grade vein that has been noted from historic maps and from exposures in the East Pit wall.  This vein is located slightly east of the Patience zone and appears to merge with the Patience zone between drill holes GQ-827 and GQ-828.  The Slusher vein was not included in the 2015 Technical Report. (CNW Group/Golden Queen Mining Co. Ltd.)

*Drawing illustrates the farthest extents of both the current modeled resources/reserves and the structures of interest to the drilling program.  The Slusher vein is a small, but slightly higher-grade vein that has been noted from historic maps and from exposures in the East Pit wall.  This vein is located slightly east of the Patience zone and appears to merge with the Patience zone between drill holes GQ-827 and GQ-828.  The Slusher vein was not included in the 2015 Technical Report.

Additional interpretive work must be completed before these initial geologic observations are proven true. Additional assays, when received, should assist with testing the grade continuity of all these structures from section to section.

Quality Assurance and Quality Control Procedures

The Main Pit 2 Infill Drilling Program is being accomplished with Reverse Circulation ("RC") drilling methods using an established contractor, Boart Longyear of Elko, Nevada. Each drill hole has been sampled on five-foot intervals throughout the entire length of the hole, and every interval drilled has been submitted to the independent lab for analysis. On average, approximately eight to ten kg of RC drill cuttings were sent to the lab for each five-foot drill interval. All sampling was conducted under the supervision of the Company's Qualified Person and/or project geologists, and the chain of custody from the project to the independent lab was continuously monitored. The Company submits approximately 10 to 15% of the samples in the form of blanks; standard reference materials and field duplicates for Quality Assurance/Quality Control ('QA/QC') purposes. In addition, the independent lab also completes their own set of QA/QC checks on the Company's submitted samples. The analytical results of all QA/QC samples have been reviewed prior to the release of this data. All analytical results have also been reviewed for their geological context and checked against the drill logs.

The independent laboratory used for this project was Bureau Veritas Mineral Laboratories ('BV') of Sparks, Nevada, an ISO 9001:2000 certified laboratory. Drill samples were picked up at Soledad Mountain by a BV employee and taken to the BV laboratory, where the samples were crushed, pulverized, digested and analyzed. All samples were analyzed for gold and silver. Gold analyses were completed using fire assay fusion and an atomic absorption spectroscopy ('AAS') finish on a 30-gram split (FA430-Au method). Silver analyses were completed using aqua regia digestion and an atomic absorption spectroscopy finish (AQ400-Ag method).

Drill hole deviation was measured by north-seeking, gyroscopic down hole surveying tools completed on all holes by Minex of Elko, Nevada. Final collar locations were surveyed by differential GPS by on-staff mine surveyors.

Technical Information  

The scientific and technical content of this news release was reviewed, verified and approved by George F. Klemmick, BSc. Geology and CPG-10937, independent consulting geologist, and a qualified person as defined by National Instrument 43-101.

About Golden Queen Mining Co. Ltd.:

Golden Queen is an emerging gold and silver producer holding a 50% interest in an open pit, heap leach mining operation on the Soledad Mountain property, located just outside the town of Mojave in Kern County in southern California.

Caution with Respect to Forward-looking Statements:  Except for statements of historical fact contained herein, the information in this press release includes certain "forward-looking information" or "forward-looking statements" within the meaning of applicable Canadian and U.S. securities legislation. Forward-looking statements can generally be identified by the use of forward-looking terminology such as "will continue to", or similar terminology.  Forward-looking statements include but are not limited to, statements related to the potential that the results of the ongoing infill drilling program, once completed, will support expansion of the mine plan area as well as plans and intentions with respect to activities on the Project. There can be no assurance that such statements will prove to be accurate, and actual results and future events could differ materially from those anticipated in such statements.  Forward-looking information is based on reasonable assumptions that have been made by the Company as at the date of such information and is subject to known and unknown risks, uncertainties and other factors that may cause the actual results, level of activity, performance or achievements of the Company to differ materially from statements in this press release regarding our intentions including, without limitation, risks and uncertainties regarding results of future drilling supporting theoretical interpretation based on limited drill data, the uncertainties inherent in the interpretation of the results of exploration drilling in general, and other risks and uncertainties disclosed in the section entitled "Risk Factors" contained in our Annual Report on Form 10-K for the year ended December 31, 2017. Investors are cautioned that forward-looking statements are not guarantees of future performance and, accordingly, investors should not put undue reliance on forward-looking statements. Any forward-looking statement made by the Company in the press release is based only on information currently available to us and speaks only as of the date on which it is made. The Company does not undertake to update any forward-looking information that is contained or incorporated by reference herein, except in accordance with applicable securities laws.

SOURCE Golden Queen Mining Co. Ltd.

View original content with multimedia: http://www.newswire.ca/en/releases/archive/April2018/03/c4083.html

Share to Youtube Share to Facebook Facebook Share to Linkedin Share to Twitter Twitter Share to Tiktok